![]() ![]() Both terry cloth and microfiber will be useful. Hand tighten the water connection back to the toilet. 1 Gather Tools and Materials You will need multiple cleaning cloths to complete this project. If you are having other plumbing work done, they might do it cheaper, and if they have a large travel fee, you may pay closer to.Add the toilet cap to the closet bolt.Use the mini hacksaw to carefully cut the closet bolts close to the nut. Before you install a new toilet, youll want to make sure your water is turned off and the old wax ring is removed from the drain (you can do this using a.Take turns securing each side and do not overtighten to prevent damaging the toilet. You'll need a new wax ring, a couple of flange bolts, a tube of. Secure them on both sides with the open-ended adjustable wrench. Installing your own toilet is a simple DIY project that will save you up. Put the washer and nut back on each closet bolt.Our own DIY experience for four toilet installations were: Toilet 1: 3.5 hours which included a few hardware store runs. If it will compress more, consider getting one with a flange to limit wax extrusion into the drainage path. If it will compress less, you need a taller ring. If all supplies are on hand, it will generally take between 45 minutes to an hour to install a new toilet. The wax ring should be compressed around 1/2 to 3/4 its initial height once installed. Add the toilet cap base to the closet bolts on both sides. Run the wax ring under hot water to soften.Carefully put the toilet back on the flange and push to set into the wax ring.It will make it easier to put the toilet back on. Buy ones with plastic tabs on them so they stay in place. The ring is so wide it slightly covers the bolt holes. Insert new closet bolts into the flange. The ring does not fit snug on the outlet on the bottom of the toilet, should it Toilet outlet OD is about 2.5' and the wax ring ID is about 3.5'.Check to ensure the closet flange is intact.Wearing gloves, remove the wax around the flange using a putty knife.Place the toilet on a piece of plywood or drop cloth to protect the floor. ![]() Use the grips under the toilet to carefully lift the toilet straight up off the bolts.Use the open-ended adjustable wrench to loosen the closet bolts on both sides of the toilet.It usually can be loosened with hands alone. You can buy a close quarters blade holder at home centers and hardware stores, or just wrap a bare blade with a rag or duct tape. In that case, a hacksaw blade is the solution. Years of corrosion can weld them to their bolts. Break the water connection from the hose to the toilet tank. Frozen bolt fix Don’t be surprised if the old nuts that hold the toilet in place won’t budge.The rest can be removed with a sponge and a bucket. Flush the toilet to drain out as much water as possible. Made from a molded wax loop around a short plastic tube, wax rings are designed to fit almost any toilet and floor drain by conforming to the shape and size of.The shutoff valve should be to the left of the toilet. Wipe any excess wax off with paper towels and then put some Clean Green on a cloth to remove the rest. Make sure that the wax seal is packed nicely all around the join and that there are no gaps.ĥ. Gently remove the new wax seal from the container and start to pack this around the join between the back of the toilet and the outlet pipe (see image above). 5 Best Toilet Wax Ring (Plus Wax-Free Seal) 5 Best Toilet Wax Ring (Plus Wax-Free Seal) If you’re buying a new toilet you’ve probably thought about installing it yourself. If you can't, do not worry too much - you can pack the new wax seal into the gap.Ĥ. ![]() Place an old towel under the pipe to catch any remaining water and pull out the old seal. Flush the toilet to empty any water in the cistern and use a plastic cup (put on your rubber gloves!)to remove any remaining water in the 'U' trap - or bend in the toilet, otherwise you will end up with water all over the floor!ģ. The main stop valve is normally located outside the house but still on your property, and is situated closely to the water meter.Ģ. ![]() If you don't have a local valve, switch off the main water supply. Lift the tank into place, making sure each of the tank bolts. Switch off the local stop valve next to the toilet. If you purchased a two-piece toilet, you’ll need to install the tank.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |